|
|
|
ACTIVE
INGREDIENT:3-Iodo-2-propynl butyl carbamate . . .
. . . . . . . . . .. . . . . . . . 40%
OTHER INGREDIENTS: . . . .. . . . . 60%
TOTAL . . . . . . . . . . . . . . . . . . .. . . .
.100%
Contains 3.88 lbs. active ingredient per gallon
KEEP OUT
OF REACH OF CHILDREN
DANGER
PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS AND DOMESTIC
ANIMALS
DANGER: Corrosive. Causes skin burns and irreversible
eye damage. Do not get in eyes, on skin, or on clothing.
Wear goggles or face shield, protective clothing, chemical-resistant
(such as nitrile or butyl) gloves. Wash thoroughly with
soap and water after handling. Remove contaminated clothing
before reuse. Harmful if swallowed, inhaled, or absorbed
through skin. Avoid breathing vapor or spray mist. Prolonged
or frequent repeated skin contact may cause allergic
reactions in some individuals.
FIRST AID
(PRACTICAL TREATMENT)
IF IN EYES:
Hold eyelids open and flush with a steady, gentle stream
of water for 15 minutes. Get medical attention.
IF ON SKIN: Wash with plenty of soap and water. Get
medical attention.
IF SWALLOWED:
Call a physician or poison control center. Do not induce
vomiting. Drink promptly a large quantity
of milk, egg whites, or gelatin mixture, or if these
are not available, large quantities of water. Avoid
alcohol. Do not give anything by mouth
to an unconscious person. IF INHALED: Remove victim
to fresh air. If not breathing, give
artificial respiration, preferably mouth-to-mouth. Get
medical attention.
NOTE TO PHYSICIAN:
Probable mucosal damage may contraindicate the use of
gastric lavage.
Net Contents _____ Gallons
EPA Reg. No. 72304-6 EPA Est. No. 45359-NC-1
Manufactured for:
SOSTRAM® CORPORATION
300 Colonial Center Parkway, Suite 230
Roswell, GA 30076
ENVIRONMENTAL
HAZARD
This pesticide is toxic to fish and aquatic organisms.
Do not discharge effluent containing this product into
lakes, ponds, streams, estuaries, oceans or public waters
unless in accordance with the requirements of a National
Pollutant Discharge Elimination System (NPDES) permit
and the permitting authority has been notified in writing
prior to discharge. Do not discharge effluent containing
this product to sewer systems without previously notifying
the local sewage treatment plant authority. For guidance
contact your State Water Board or Regional Office of
the EPA.
STORAGE
AND DISPOSAL
PESTICIDE DISPOSAL — Keep container tightly closed
when not in use. Do not reuse container. Do not store
with strong oxidizing agents or strong (concentrated)
acids. Do not contaminate water, food, or feed by storage
or disposal. Pesticide wastes are acutely hazardous.
Improper disposal of excess pesticide, spray mixture,
or rinsate is a violation of Federal Law. For wastes,
which cannot be disposed of by use according to label
instructions, contact your local State Pesticide or
environmental Control Agency, or the Hazardous Waste
representative at the nearest EPA Regional Office for
guidance.
CONTAINER DISPOSAL —
Triple rinse container. Then offer for recycling or
reconditioning, or puncture and dispose of in a sanitary
landfill, or incineration or, if allowed by state and
local authorities, by burning. If burned stay out of
smoke.
DIRECTIONS FOR USE
It is a violation of Federal law to use this product
in a manner inconsistent with its labeling. This formulation
is not cleared by Federal Food, Drug and Cosmetic Act
for use in manufactured food grade adhesive, paper and
paper board products and paper coating.
ADHESIVES
PROTRAM™ 40 can be used as an additive to non-medical,
non-food use natural and synthetic adhesive formulations
and caulks to prevent the growth of fungal organisms
in the material both in the wet state and in the dry
film of the finished product. Recommended use levels
are between 0.05 - 0.625% wet formulation weight. This
product should be added toward the end of production
cycle with good agitation to ensure a uniform distribution.
For example, to inhibit the growth of mildew on a latex-based
wall cover adhesive for a non-food area add 0.5% (5
lbs. of PROTRAM™ 40 per 1000 lbs. of latex-based
adhesive
formulation) of this product to the latex-based formulation.
AQUEOUS METALWORKING, CUTTING, COOLING, & LUBRICATING
CONCENTRATES
To inhibit the growth of fungi in an aqueous metalworking,
cutting, cooling & lubricating concentrates add
an amount that will give up to 2,500 ppm in the diluted
fluid. The amount required in the concentrate will depend
on the end use dilution. For example, if the desired
level of this product in the diluted fluid is 250 ppm,
and the end use dilution of the fluid is 5%, then a
0.5% concentration of this product is required in the
concentrate (250 ppm/ 0.05 = 5,000 ppm or 0.5%). AQUEOUS
METALWORKING, CUTTING, COOLING, & LUBRICATING FLUIDS
To inhibit the growth of fungi in an aqueous metalworking,
cutting, cooling & lubricating fluids add up to
2,500 parts per million (0.25% v/v) of this product
to the diluted fluid (1 quart per 100 gallons of solution
or 2.5 liters per 1000 liters). This product may be
added to the fluid at the time it is prepared (diluted)
or to the reservoir (sump) containing the fluid after
it is put into use. If it is added to the reservoir,
the fluid should be circulated after addition to ensure
mixing.
CORDAGE
PROTRAM™ 40 may be used as a mildewcide in both
aqueous and solvent based process formulations, which
coat cordage. Typical use levels of this product will
range from 0.05 - 2.5% of the process formulations used
in the process of these cordages. This product should
be added to the process formulation at the end of the
production cycle with good agitation to prevent possible
mechanical losses and to ensure a uniform distribution.
As an example, to inhibit the growth of mildew on cordage
intended for a non-food area add 1.25% (12 lbs. PROTRAM™
40 per 1000 lbs. of process formulation) of this product
to the process formulation.
INKS
PROTRAM™ 40 may be used in aqueous-based ink solutions
for protection of these solutions against attack by
fungal organisms. It is recommended that this product
be added at the end of the production cycle with good
agitation. This product will generally impart protection
when used at levels of 0.05 - 3.0% of active ingredient
based on the formula weight.
PAINTS
AND STAINS
PROTRAM™ 40, used in solvent and waterborne paints
and stains, will inhibit the growth of mildew. Addition
should be at the end of the manufacturing process and
allowed to mix long enough to be adequately dispersed
and should not be added to hot paint. Typical levels
for protection against mildew on painted surfaces are
0.25 - 1.2% by weight on wet paint. For example, house
paint with a wet density of 10 lbs. per gallon would
use 2.5 - 12.0 lbs. of this product per 100 gallons
of wet paint. Where the climate is severe and mildew
growth is a major problem for painted surfaces, more
would be required, as much as 2.0% by weight in the
paint. For interior paint use, approximately half the
exterior concentrations should be used, 0.1 - 0.6% by
weight in the paint. Appropriate levels are best determined
by field trials.
PLASTICS AND PLASTIC COATINGS
PROTRAM™ 40 may be used to prevent surface mildew
growth on plastic items such as shower curtains, cable
and wire insulation and sun umbrellas. Intended plastics
include polymers such as PVC. Use levels of 0.1250 -
2.5% by weight of the plastic are generally adequate.
This product should be dispersed in the plasticizer
or color concentrate before it is incorporated into
the resin to ensure a uniform distribution. Use of this
product is not recommended if the heat of processing
is above 350 oF for prolonged periods, nor should it
be used in a plastic that will be in contact with food
or medical device applications.
PAPER COATINGS
PROTRAM™ 40 may be used as a mildewcide in both
aqueous and solvent-based coatings, which are applied
to paper and cardboard substrates. This product can
be used to prevent mold and mildew from growing on products
such as: corrugated cardboard or soap wrappers, wall
covers, non-food contact packaging materials, and non-food
contact paper tapes. Use levels of this product range
from 0.05 - 2.0% of this product by weight. This product
should be added at the end of the production cycle and
with good agitation to prevent possible mechanical losses
and to ensure uniform distribution. As an example, to
inhibit growth of mildew on corrugated cardboard intended
for a non-food packaging add 1.25% (12.5 lbs. PROTRAM™
40 per 1000 lbs. of coating material) of this product
to the coating material formulation.
WOOD PRESERVATION
PROTRAM™ 40 is a liquid designed for use as an
additive to interior or exterior protective coatings
to inhibit the growth of mildew on the film surface.
It is also recommended as a wood preservative for use
in above ground applications. All recommendations of
use levels are in percentage by weight, and refer to
this product. Dosage ranges are given for the various
applications to indicate the approximate levels for
a particular application. Exact levels of use should
be determined by field trials.
PROTRAM™ 40 may be applied from solvent solutions
or aqueous dispersions to new lumber, plywood, particle
board, millwork, etc., to prevent the growth of mildew,
sapstain and wood rot on these substrates. This product
is recommended for use on wood in above ground use only.
Treating solutions may be prepared by diluting this
product in alcohols or aromatic solvents or by dispersion
in water. Levels of 0.25 - 3% of this product are suggested
depending upon the severity of conditions for end use,
and the extent of time that protection is required.
For freshly sawn lumber, a concentration of 0.5% of
this product is suggested as a starting level. A one
minute dip at ambient temperatures in a solution or
aqueous dispersion containing 0.5% of this product should
be adequate to control the development of mildew and
sapstain organisms on the lumber. Because of the great
variation in susceptibility of fresh sawn lumber relating
to the type of wood, sawing and storage techniques,
conditions of humidity, method of treatment, etc., it
is usually necessary to carry out field tests to determine
the most appropriate means of application and the optimum
concentration of this product to be used within the
range specified.
For best results, lumber should be treated within twenty-four
hours after it is sawed. The lumber should be completely
immersed in the treating bath, and the treating vat
designed to permit easy immersion and removal, and to
minimize spillage. The vat may be cleaned by emptying
and rinsing with a suitable solvent or by use of a detergent
solution. To add additional product while treating,
first prepare the proper solution or emulsion in a separate
container (of wood, plastic, or stainless steel construction)
and add to the treating vessel.
After treatment, lumber should be stacked in a properly
maintained seasoning yard with good drainage so that
no water will accumulate, in any area. The yard should
be kept free from weeds and vegetation, which may hold
moisture and promote growth of decay and stain producing
fungi. All debris and lumber scraps should be removed
from the area. A properly laid out yard should take
advantage of prevailing winds to permit good air circulation.
Main alleys should be at least 16 feet wide. Stack foundations
should be sufficiently elevated to permit ready access
of air to the pile, and allow water to drain off quickly.
WARRANTY
AND LIMITATIONS OF DAMAGES
CONDITIONS OF SALE: Sostram Corporation warrants that
this product conforms to the chemical description stated
on the label when used in accordance with the directions
under normal conditions of use. This warranty does not
extend to the use of this product contrary to label
instructions, or under abnormal use conditions, or under
conditions not reasonably foreseeable to Sostram. SOSTRAM
DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING ANY WARRANTY OF FITNESS OR MERCHANTABILITY.
SOSTRAM SHALL NOT BE LIABLE FOR CONSEQUENTIAL, SPECIAL,
OR INDIRECT DAMAGES RESULTING FROM THE USE OR HANDLING
OF THIS PRODUCT, AND SOSTRAM'S SOLE LIABILITY AND BUYER'S
AND USER'S EXCLUSIVE REMEDY SHALL BE LIMITED TO THE
REFUND OF THE PURCHASE PRICE. BUYER AND USER ACKNOWLEDGE
AND ASSUME ALL RISKS AND LIABILITY RESULTING FROM HANDLING,
STORAGE AND USE OF THIS PRODUCT. SOSTRAM DOES NOT AUTHORIZE
ANY AGENT OR REPRESENTATIVE TO MAKE ANY OTHER WARRANTY,
GUARANTEE OR REPRESENTATION CONCERNING THIS PRODUCT.
|
